Featured Products
$179.99
19 inch CGA-EGA-VGA-SVGA LCD arcade monitor
Quantity Left: 0
Games Rooms Games for Sale
Profile for jean
User: jean
Registered: May-10-2011
Favorite Links
most of the mak vision monitors use a phillips tube and do not use convergence rings as such. it is all in yoke positioning. ...
Tread: Makvision/Wei D2929 adjustments
Tread: Makvision/Wei D2929 adjustments
what you discribe is called blooming. It willoccour when the high voltage is groosly out of adjustment. Stop using the monito...
Tread: D9400 color and scanline questions
Tread: D9400 color and scanline questions
galaga turns the tube 90 degrees so what you are calling verticle is actualy the horizontal axis of the tube. adjust h hold t...
Tread: Monitor wont focus/converge, i need help!
Tread: Monitor wont focus/converge, i need help!
you need to be very carful. there a voltages that you will be cloise to that can deliver a nasty shock. onley touch plastic. ...
Tread: crt is grey with white lines at a 45 degree angle
Tread: crt is grey with white lines at a 45 degree angle
repair the monitor. lcd screens are expensive and realy not viable for a basement arcade unless you have the the money to spe...
Tread: To Upgrade or Not to Upgrade
Tread: To Upgrade or Not to Upgrade
you have no video drive and your screen is set to high. the lines are called retrace lines. the tubes coduction is so high it...
Tread: crt is grey with white lines at a 45 degree angle
Tread: crt is grey with white lines at a 45 degree angle
check the yoke connections and solder in the yoke circuit. mesur the horizontal coil. it should be around 1.2 to 2 ohms. meny...
Tread: CRT Monitor only displays a color point in the center of screen
Tread: CRT Monitor only displays a color point in the center of screen
the cap under the hop heat sink is the one but replace thm all anyway
Tread: My monitor has vertical bars running on left side
Tread: My monitor has vertical bars running on left side
check your yoke connections. also verify the yoke impedances math your chassis
Tread: G07 Blown F901 Fuse Problem
Tread: G07 Blown F901 Fuse Problem
check the cathode voltages on the crt. they should be around 100 volts for each gun.reolder trhe connections on the neck bo...
Tread: Midway cabinet-color problem
Tread: Midway cabinet-color problem
Check solder connections during your recap. it is quit possible tha it is going into high voltage shutdown in wich case you n...
Tread: Monitor works and then goes dark/blind
Tread: Monitor works and then goes dark/blind
I am blessed with maintaining about 200 tube based monitors. They are quit old so iI have had to build about a hundred . I p...
Tread: Green bleeding when first turned on ....
Tread: Green bleeding when first turned on ....
Generaly diagnosing a bad crt is not at all difficult. three simple voltage mesurments tell the story . turn the brightness a...
Tread: wells 2794 weak red/no red
Tread: wells 2794 weak red/no red
most monitor chassis can be reconfigured for etir vertical or hrizontal. you must completly remove the tube to do it. if you...
Tread: Can I move my monitor from horizontal to vertical
Tread: Can I move my monitor from horizontal to vertical
it does not sound good. first check the wire pins on the crt neck. are any bent? the heater pins are labled h thier are 2 o...
Tread: Hantarex POLO3/ 10 monitor dead, chassis good...
Tread: Hantarex POLO3/ 10 monitor dead, chassis good...
Page 1 of 1